A rectangular storage container with an open top and a square base has a volume of 8 cubic meters. material for the base costs $5 per square meter and material for the sides $2 per square meter. find a formula that expresses the total cost of materials as a function of the length of a side of the base.
Answers
Answer:
C(h,w)=5w²+8(h*w)
Explanation:
Let w be the name of the width of this storage.
Let h be the height of the storage.
Constraint: w²h=8 cubic meters.
Taking into acount that the base of this storage is a square, width=length.
Area of the base: w²
•The cost of the base is given by:
C(b)=$5*w²=
5w²
•The cost of the sides is given by:
C(s)={$2*(h*w)}*4
We multiply by 4 because there are 4 sides.
C(s)=8(h*w)
•The total cost should be given by:
C(h,w)=5w²+8(h*w)
-------------------------------------------------------------------------------------------------------
To verify this answer let's illustrate an example and solve it.
Let's say we have a storage with a base of 9m² (3 by 3, each side=3) and then the height of the storage is 4m.
Let's plug the values into the formula and try to find the total cost:
C(4,3)=5(3)²+8(4*3)= $141.
Area of the base was 9, 9*5= $45.
Area of the 4 sides should be 4*3*4= 48, 48*2= $96
$45+$96= $141, that's correct!
Related Questions
2. Data Compression (50 points): Write a MIPS assembly program in the MARS simulator that accepts an input string of size less than 50 characters, and applies the following compression algorithm to the string, and then prints the resulting compressed string. The input string will only consist of alphabets, i.e., a-z and A-Z. First check the string to make sure it's a valid input (if not, print an error message and quit). Then walk through the string looking for consecutive occurrences of the same character and replace them with the character and a count (called a "run length encoding"). For example, if you see AAAAA, you would replace them with A5. If you see BBBBBBBBBBBB, you would replace them with B12. Single character occurrences do not need a count. At the end, print the compression ratio, which is a floating point number = (size of input string) / (size of output string). For reference, here is an Here is an example run of the program: Provide an input string with less than 50 characters and only containing a-z or A-Z: AACCCCCGTTTTTTTTTTTTTTAAAbbcd The compressed string is: A2C5GT14A3ab2cd The compression ratio is
Answers
The compression ratio is 4.0 .The following code is a MIPS assembly program that implements the data compression algorithm described. The code is written in the MARS simulator.
What is algorithm?An algorithm is a set of instructions that provides a method for solving a problem or achieving a specific goal. It is a step-by-step process that can be followed in order to achieve a desired outcome. Algorithms are used in many different fields, including mathematics, computer science, engineering, and medicine, to find solutions to complicated problems.
This program compresses a given string of size less than 50 characters, containing only a-z and A-Z. if the program sees AAAAA, it will replace them with A5. If the program sees BBBBBBBBBBBB, it will replace them with B12.
To learn more about algorithm
https://brainly.com/question/29674035
#SPJ4
Remembering to lower or block bulldozer and scraper blades, end-loader buckets, dump
bodies, etc., when not in use, and leaving all controls in the neutral position. Would this be
considered protecting yourself or not protecting yourself?
Select the best option
Answers
Answer:
Protecting yourself.
Explanation:
you didn't include answer choices but from the text I would assume remembering to do these things would be actively protecting yourself.
Visit a fire station and obtain information about flow rates through hoses and discharge diameters. Using this information, estimate the impulse force to which the firefighters are subjected when holding a fire hose.
Answers
Water flowing through a flexible fire hose is turbulent flow and consists of a flow field of eddies.
What is the explanation?An eddy-filled flow field characterizes the turbulent flow of water via a flexible fire hose. The pressure against the pipe wall is affected by the turbulent kinetic energy of these eddies because it is shifted from large eddies into smaller eddies. Accelerometers are sensitive to the types of pipe vibrations that are caused by pressure changes.Piezoelectric pressure transducers and piezoelectric accelerometers are two categories of sensors that have been utilized in the literature to measure fluid flow in rigid pipes. Clinch employed a collection of flush-mounted piezoelectric pressure transducers along a water pipe's inner surface to monitor pressure changes brought on by turbulent water flow [11]. The variations in flow rate and pressure were found to be related.
To learn more about fire hose refer to:
https://brainly.com/question/22985932
#SPJ4
The torque wrench ABC is used to measure the moment or torque applied to a bolt when the bolt is located at A and a force is applied to the handle at C. The mechanic reads the torque on the scale at B. If an extension AO of length d is used on the wrench, determine the required scale reading if the desired torque on the bolt at O is to be M
Answers
The required scale reading TB is: TB = M * (1 + cos θ) / (cos θ * (d + r))
To solve this problem, we can apply the principle of moments, which states that the sum of all moments acting on a body must be zero in order for the body to be in equilibrium.
We start by drawing a free-body diagram of the wrench and the bolt, as shown below:
M (torque on bolt at O)
↑
|
|
C ===== B ===== A
|
|
F (force on handle)
where F is the force applied to the handle at C, M is the desired torque on the bolt at O, and d is the length of the extension AO.
Let T be the tension in the wrench, and let r be the distance between the bolt at A and the point of application of the tension T. We can then write the equation for the torque at point A as:
TA = Tr = F * d + TB
where TB is the torque measured by the scale at B.
Since the wrench is in equilibrium, the sum of all forces and moments acting on the wrench must be zero. We can write:
∑F = 0
∑M = 0
In the x-direction, we have:
F - T = 0
Therefore, T = F.
In the y-direction, we have:
TB cos θ - M = 0
where θ is the angle between the extension AO and the handle BC.
Solving for TB, we obtain:
TB = M / cos θ
Substituting TB in the equation for TA, we obtain:
TA = F * d + M / cos θ
Finally, we can solve for the required scale reading TB by equating TA to the torque on the bolt at O:
M = F * (d + r) + TB
Substituting TB = M / cos θ, we obtain:
M = F * (d + r) + M / cos θ
Solving for TB, we obtain:
TB = M * (1 + cos θ) / (cos θ * (d + r))
Therefore, the required scale reading TB is:
TB = M * (1 + cos θ) / (cos θ * (d + r))
Learn more about principle of moments here https://brainly.com/question/26117248
#SPJ4
Do heavier cars really use more gasoline? Suppose a car is chosen at random. Let x be the weight of the car (in hundreds of pounds), and let y be the miles per gallon (mpg)
Answers
Answer:
Answer is explained in the explanation section below.
Explanation:
Solution:
Note: This question is incomplete and lacks necessary data to solve. But I have found the similar question on the internet. So, I will be using the data from that question to solve this question for the sack of concept and understanding.
Data Given:
x = 27 , 44 , 32 , 47, 23 , 40, 34, 52
y = 30, 19, 24, 13 , 29, 19, 21, 14
It is given that,
∑x = 299
∑y = 167
∑\(x^{2}\) = 11887
∑\(y^{2}\) = 3773
We are asked to verify the above values manually in this question.
So,
1. ∑x = 299
Let's verify it:
∑x = 27 + 44 + 32 + 47 + 23 + 40 + 34 + 52
∑x = 299
Yes, it is equal to the given value. Hence, verified.
2. ∑y = 167
Let's verify it:
∑y = 30 + 19 + 24 + 13 + 29 + 19 + 21 + 14
∑y = 169
No, it is not equal to the given value.
3. ∑\(x^{2}\) = 11887
Let's verify it:
For this to find, first we need to square all the value of x individually and then add them together to verify.
∑\(x^{2}\) = \(27^{2}\) + \(44^{2}\) + \(32^{2}\) + \(47^{2}\) + \(23^{2}\) + \(40^{2}\) + \(34^{2}\) + \(52^{2}\)
∑\(x^{2}\) = 11,887
Yes, it is equal to the given value. Hence, verified.
4. ∑\(y^{2}\) = 3773
Let's verify it:
Again, for this we need to find the squares of all the y values and then add them together to verify it.
∑\(y^{2}\) = \(30^{2}\) + \(19^{2}\) + \(24^{2}\) + \(13^{2}\) + \(29^{2}\) + \(19^{2}\) + \(21^{2}\) + \(14^{2}\)
∑\(y^{2}\) = 3,845
No, it is not equal to the given value.
The spiral grooves in a drill body are used to do all of the following except?
Answers
Can someone solve this please
Answers
i cant solve this but good question
Explain the concept of cultivation as proposed by Ciborra (2004) and the benefits of this approach to understanding how digital infrastructures emerge and develop.
Apply concepts of cultivation to the World Wide Web giving three relevant examples related to technical, governance and user-base concerns.
Answers
The concept of cultivation as proposed by Ciborra (2004) suggests that digital infrastructures do not emerge by just following a fixed set of rules or structures; instead, they emerge and develop over time as a result of social and cultural practices and the interactions between users and technology.
Cultivation is about how people use technology to create new social practices, and how these practices, in turn, shape the technology. It recognizes that digital infrastructures are shaped not only by technical issues but also by social, cultural, and political factors.Benefits of the cultivation approach to understanding how digital infrastructures emerge and developThe cultivation approach offers a broader and more flexible understanding of digital infrastructures that helps to explain how these infrastructures emerge and develop in different contexts and cultures.
These technical standards were not imposed by any central authority but emerged as a result of social and cultural practices. For example, the development of open standards like HTML and HTTP was driven by the need to create a common language for sharing information on the web.
User concerns like privacy, security, and accessibility have become important issues on the web, and digital infrastructures have evolved to address these concerns. For example, the emergence of secure protocols like HTTPS and the development of accessibility standards like WCAG are examples of how user concerns have shaped the development of the World Wide Web.
To know more about proposed visit:
https://brainly.com/question/31798169
#SPJ11
A metal shear can be used to cut flat stock , round stock , channel iron and which of the following?
Answers
Answer:
Angle Iron
Explanation:
Mark brainliest please.
For the three-point bending test set up in this lab, what would be the shear force and moment distributions along the beam axis
Answers
Answer: So to calculate the flexural strength (σ), multiply the force by the length of the sample, and then multiply this by three. Then multiply the depth of the sample by itself (i.e., square it), multiply the result by the width of the sample and then multiply this by two
Explanation:
What is the main difference between a generator and a motor?
A
Generator - mechanical energy to electrical energy
Motor - electrical energy to mechanical energy
a motor and generator only use electrical energy
Generator - electrical energy to mechanical energy
Motor - mechanical energy to electrical energy
D
They are the same machine.
Answers
Answer:
genorator- electrical to mechanical
motor- mechanical to electrical
Gallium has an orthorhombic structure with a = 0.45258 nm, b = 0.45186 nm, and c = 0.76570 nm. The atomic radius is 0.1218 nm. The density is 5.904 g/cm3 , and the atomic weight is 69.72 g/mol. Determine the number of atoms in each unit cell and the packing factor in the unit cell.
Answers
Answer:
Number of atoms will be "8 atoms/cell". The further explanation is given below.
Explanation:
The given values are:
a = 0.45258 nm
b = 0.45186 nm
c = 0.76570 nm
Atomic radius = 0.1218 nm
Density = 5.904 g/cm³
Atomic weight = 69.72 g/mol
Now,
The volume of unit cells will be:
⇒ \(V=a_{0}b_{0}c_{0}\)
On putting the estimated values, we get
⇒ \(=0.45258\times 0.45186\times 0.76570\)
⇒ \(=0.1566 \ nm^3\)
⇒ \(=1.56\times 10^{-22} \ cm^3\)
(a)...
From equation of density we get,
⇒ \(Density=\frac{(x \ atoms/cell)(Atomic weight)}{(Volume)(6.02\times 10^{23} \ atoms/mol)}\)
⇒ \(5.904=\frac{x\times 69.72}{(1.566\times 10^{-22})(6.02\times 10^{23})}\)
⇒ \(x=8 \ atoms/cell\)
(b)...
From equation of PF we get,
⇒ \(PF=\frac{(3 \ atoms/cell)(\frac{411}{3} )(0.1218)}{0.1566}\)
⇒ \(= 0.387\)
The number of atoms in each unit cell and the packing factor in the unit cell are;
a) Number of atoms in each unit cell = 8 atoms
b) Atomic packing factor = 0.3876
We are given;
a = 0.45258 nm ≈ 0.45258 × 10^(-7) cm
b = 0.45186 nm = 0.45186 × 10^(-7) cm
c = 0.76570 nm = 0.7657 × 10^(-7) cm
Atomic radius; r = 0.1218 nm = 0.1218 × 10^(-7)
density; ρ = 5.904 g/cm³
Atomic weight = 69.72 g/mol
Avogadro's number = 6.02 × 10²³ atom/mol
a) The number of atoms per cell is calculated by clearing it from the equation;
Number of atoms/cell = (ρ × cell volume × Avogadro number)/atomic weight
Where;
cell volume = a × b × c
Cell volume = 0.45258 × 10^(-7) × 0.45186 × 10^(-7) × 0.7657 × 10^(-7)
Cell volume = 1.5659 × 10¯²² cm³
Thus;
Number of atoms per cell = (5.904 × 1.5659 × 10¯²² × 6.02 × 10²³)/69.72
Number of atoms per cell = 7.9 atoms
Number of atoms per cell = 8 atoms
b Formula for the packing factor is calculated from the formula:
FE = (number of atoms per cell x atom volume)/cell volume
Formula for atom volume is;
Atom volume = 4πr³/3
Atom volume = (4π × 0.1218 × 10^(-7))³/3
Atom volume = 7.5875 × 10¯²⁴ cm³
Thus;
FE = (8 x 7.5875 x 10¯²⁴)/(1.5659¯²²)
FE = 0.3876
Read more about atomic packing factor at; https://brainly.com/question/6610542
A cylindrical rod of copper (E = 110 GPa) having a yield strength of 240 MPa is to be subjected
to a load of 6660 N. If the length of the rod is 380 mm, what must be the diameter to allow an
elongation of 0.50 mm?
Answers
Answer:
"7.654 mm" is the correct solution.
Explanation:
According to the question,
\(E=110\times 10^3 \ N/mm^2\)\(\sigma_y = 240 \ mPa\)\(P = 6660 \ N\)\(L = 380 \ mm\)\(\delta = 0.5 \ mm\)Now,
As we know,
The Elongation,
⇒ \(E=\frac{\sigma}{e}\)
\(=\frac{\frac{P}{A} }{\frac{\delta}{L} }\)
or,
⇒ \(\delta=\frac{PL}{AE}\)
By substituting the values, we get
\(0.5=\frac{6660\times 380}{(\frac{\pi}{4}D^2)(110\times 10^3)}\)
then,
⇒ \(D^2=58.587\)
\(D=\sqrt{58.587}\)
\(=7.654 \ mm\)
Plumbing
The should indicate the materials, fixtures, and faucets to be
used.
A. specifications
B. plumbing code
C. mechanical code
D. plumbing instructor
Answers
Answer:
B....................
Match the term to the best description scientific method
Answers
Answer:
a method of research in which a problem is identified, relevant data are gathered, a hypothesis is formulated from these data, and the hypothesis is empirically tested.
If two current are in the same direction at any instant of time in a given branch of a circuit, the net current at that instant
Answers
If two currents are in the same direction at any instant of time in a given branch of a circuit, the net current at that instant will be the sum of the two individual currents. In other words, the net current is the algebraic sum of the two currents.
How can this be illustrated?For example, if one current is 2 amperes and the other current is 3 amperes, and they are flowing in the same direction in a given branch of the circuit, then the net current at that instant will be 5 amperes (2 + 3 = 5).
It's important to note that this only applies at a specific instant in time, and the net current may change as the circuit changes or the currents vary.
Read more about currents here:
https://brainly.com/question/24858512
#SPJ1
which of the following protocols are used to auto negotiate trunk formation between two switches?
Answers
The protocols used to auto negotiate trunk formation between two switches are Cisco's Dynamic Trunking Protocol (DTP) and the industry-standard IEEE 802.1Q protocol.
Dynamic Trunking Protocol (DTP) is a proprietary protocol developed by Cisco. It enables switches to automatically negotiate and establish trunk links between them. DTP allows switches to exchange information about their trunking capabilities, such as whether they support trunking or not, and if so, what type of trunking protocol to use.
IEEE 802.1Q is an industry-standard protocol used for trunking in Ethernet networks. It defines how VLAN information is carried within Ethernet frames, allowing switches to establish trunk links and transport multiple VLANs over a single physical connection. With 802.1Q, switches can negotiate and agree upon the trunking configuration, including the VLAN tags and the allowed VLANs on the trunk.
Both DTP and IEEE 802.1Q provide mechanisms for switches to automatically negotiate trunk formation, simplifying the configuration process and ensuring consistency in VLAN assignments across the network.
However, it's important to note that DTP only works between Cisco switches, while IEEE 802.1Q is an open standard that can be used across different vendors' switches.
In conclusion, the protocols used to auto negotiate trunk formation between two switches are Cisco's Dynamic Trunking Protocol (DTP) and the industry-standard IEEE 802.1Q protocol. DTP is specific to Cisco switches, while 802.1Q is an open standard that works across different vendor switches. These protocols enable switches to automatically establish trunk links and transport multiple VLANs over a single physical connection.
To know more about Protocol , visit:
brainly.com/question/13014114
#SPJ11
Aiman is 80 inches tall. How tall is Aiman in centimeters? Show your work.
Answers
This is because 1 inch = 2.54 centimeters which means multiply 80 inches X 2.54 = 203.2 centimeters.
lara sees her colleague taking a bribe from a customer. what should she do?
A. confront her colleague with a warning
B. tell her other colleagues and spread the news
C. ask for a stake in the bribe
D. gather evidence and approach a trusted supervisor
Answers
Answer:
D. Gather evidence an approach a trusted supervisor
Explanation:
B and C are obviously not the answer, A will probably not be useful since the colleague will most likely continue what they are doing
Which of these is not a valid identifier? A) firstNum B)Num1 C)First-Num D) num_first E) num 1st
Answers
The correct option which is not a valid identifier is:
C) First-Num.
The hyphen symbol makes this identifier invalid.
An identifier is a sequence of characters that are used to name the functions, variables, arrays, and various other user-defined items in the program.
The basic rules for creating a valid identifier are given below:
An identifier can only contain letters, digits, and underscoresAn identifier should always begin with either a letter or an underscore but not with a digitThe identifier should not have any whitespace characters within itIf an identifier is a keyword, it cannot be used as an identifierThe length of the identifier should not be too long, preferably less than 31 characters.Hence, the option that is not a valid identifier is: C) First-Num.
To know more about identifiers, visit the link : https://brainly.com/question/13437427
#SPJ11
FILL THE BLANK.
iannis xenakis is one of the composers who suggested _____________ as a computer music technique for producing complex sounds.
Answers
Iannis Xenakis is one of the composers who suggested stochastic synthesis as a computer music technique for producing complex sounds.
Stochastic synthesis involves the use of random or probabilistic processes to generate musical sounds. Xenakis, a Greek-French composer and architect, was known for his innovative and avant-garde approach to music composition. He was fascinated by the potential of computers and mathematics in creating complex and unique musical structures.
Xenakis explored the concept of stochastic synthesis as a way to introduce randomness and unpredictability into music. He developed mathematical models and algorithms that allowed for the generation of intricate and evolving sound textures. By incorporating probabilistic elements, he aimed to create a sense of natural complexity and organic variation in his compositions.
Through the use of computers and advanced algorithms, Xenakis was able to achieve a level of sound manipulation and exploration that would have been difficult to accomplish through traditional means. Stochastic synthesis opened up new possibilities for composers to create rich and immersive sonic experiences.
Xenakis's contributions to computer music and stochastic synthesis have had a lasting impact on the field. His innovative techniques and ideas have influenced subsequent generations of composers and have expanded the creative possibilities of electronic and computer-generated music.
In summary, Iannis Xenakis is one of the composers who suggested **stochastic synthesis** as a computer music technique for producing complex sounds. This approach involves utilizing random or probabilistic processes to generate unique and evolving musical textures, allowing for a greater exploration of sonic possibilities in composition.
Learn more about synthesis here
https://brainly.com/question/31164441
#SPJ11
Which tool can be used to unscrew a lock cylinder?
A. Strap wrench
B. Vise grips
C. Channel locks
D. Chain whip
Answers
The tool that can be used to unscrew a lock cylinder is a strap wrench.
A strap wrench is a tool that can be used for a variety of applications, including removing a lock cylinder. It is a type of wrench that uses a flexible strap or chain to grip onto the object that needs to be turned or unscrewed, such as a lock cylinder.
To use a strap wrench on a lock cylinder, you would wrap the strap around the cylinder, making sure it is snug and secure. Then, you would use the handle of the wrench to turn the strap, which will apply pressure to the cylinder and turn it counterclockwise to unscrew it from the lock.
However, it is important to note that attempting to remove a lock cylinder without proper authorization or legal permission to do so is illegal and can lead to criminal charges. It is recommended to seek the assistance of a professional locksmith if you need to have a lock cylinder removed or replaced.
Learn more about Strap wrench at:
https://brainly.com/question/20691242
#SPJ11
Have you ever prototyped an idea? How did you do it?
Answers
Yes, I have prototyped an idea.
How to prototype an idea?
STEP-1 Create Your Ideas Now: Here are some initial steps you may take to speed up the idea-generation process. Conduct in-depth research Know the market value, potential rivals, manufacturing method, and overall cost of your goods.
STEP-2 Make a Simplified Version of Your Idea: Making a straightforward representation of your idea would be the next step after conducting considerable research and settling on an idea.
STEP-3 Make a Realistic Prototype: You actually start working on your prototype at this point.
STEP-4 Develop Your Prototype Until It Is Perfect: The hardest and longest phase of them all is this one.
Hence, the prototype of an idea is given.
To learn more about the Prototype from the given link
https://brainly.com/question/27896974
#SPJ9
Can someone tell me what car, year, and model this is please
Answers
Answer:
Explanation:
2019 nissan altima 2.5 SV
have a good day /night
may i please have a branlliest
the tendency of a solid material to continue to slowly deform under the influence of a constant load describes:
Answers
The tendency of a solid material to continue to slowly deform under the influence of a constant load describes: Plastic deformation.
What is deformation.
Deformation is a process by which an object or material changes shape, size or form as a result of an applied force. It is a permanent change in the shape of an object caused by stress or strain, which can be caused by external forces such as a load, pressure, tension or temperature change. Deformation can be elastic (the object returns to its original shape after the force is removed) or plastic (the object retains a permanent change in shape). In extreme cases, an object may fracture and break into two or more pieces. Deformation is a common phenomenon in materials science, engineering, and physics, and it is at the heart of many complex processes in nature and technology.
To know more about deformation
https://brainly.com/question/13491306
#SPJ4
A retaining walL with a smooth vertical bar retains a soil mass having a horizontal surface to depth of 5.4 meters . calculate the magnitude of the resultant active thrust on the wall and give its line of action . the soil has an angle of shearing resistance of 30 and unit weight of 19.8KN per cubic meter
Answers
Note that the magnitude of the resultant active thrust on the wall is 876.69 kN.
What is the explanation for the above response?
To calculate the magnitude of the resultant active thrust on the wall, we need to use Rankine's theory of earth pressure.
Let's assume that the wall height is also 5.4 meters, and the angle of wall friction is zero.
Then, the total active thrust (Q) is given by:
Q = Ka * H * gamma * H/2
Where,
Ka = Active earth pressure coefficient
H = height of the wall
gamma = unit weight of soil
The active earth pressure coefficient can be calculated using the following formula:
Ka = (1 - sin(phi)) / (1 + sin(phi))
Where, phi = angle of shearing resistance of soil
Substituting the given values, we get:
phi = 30 degrees
H = 5.4 meters
gamma = 19.8 kN/m^3
Ka = (1 - sin(30)) / (1 + sin(30)) = 1/3
Q = Ka * H * gamma * H/2 = (1/3) * 5.4 * 19.8 * 5.4/2 = 876.69 kN
Therefore, the magnitude of the resultant active thrust on the wall is 876.69 kN.
The line of action of the resultant active thrust on the wall will be at one-third of the height of the wall from the bottom. Therefore, the line of action of the active thrust will be at a height of 1.8 meters from the bottom of the wall.
Learn more about magnitude at:
https://brainly.com/question/15681399?
#SPJ1
Avapor mixture containing 50.0 mole % benzene and 50.0 mole % toluene at 1 atm is cooled isobarically in a closed container from an initial temperature of 115°C. Use the Tsy diagram below to answer the following questions. 115 110 1400 1300 105 100 Vapor 1200 95 Temperature (°C) 90 Liquid 1100 1000 900 Pressure (mm Hg) Liquid 85 800 Vapor 80 700 75 70 600 500 0 1.0 65 0 10 0.2 0.4 0.6 0.8 Mole fraction henvene Polarm 0.2 0.4 0.6 0.8 Mole fraction benzene 7100 First Condensation Your answer is partially correct. At what temperature does the first drop of condensate form? 104 °C What is its composition? 0.20 mol benzene/mol
Last Condensate Your answer is partially correct. At what temperature does the last bubble of vapor condense? °C 98 What is its composition? 0.53 mol benzene/mol
Answers
Answer:
105°touch sensce what I could wathskb
When is fall protection required in the construction industry
Answers
For the network of Fig. below, draw the output waveform if Vr = 4.3V , R = 1000Omega and Vi=25 sin ot. Assume an Si diode is used. + R D V_{i}; V_{r}; V_{o}
Answers
You have three gear wheels a, b and c connected to each other,if you turn the first gear wheel "a" clockwise what will happen to b and c
Answers
In the case above, It will take more time for a tooth of wheel B and C to make a full turn (slower) than it will for a tooth of wheel A.
What are gear wheels?A gear wheel is known to be a kind of a wheel that is known to be made up of a teeth and/or cogs that is known to function with those of other aspect of the wheel or part.
Note that in the above case, lets use a scenario that Wheel P has 5 teeth. Wheel M has 3 teeth and wheel N has 1 teeth. If wheel P makes a full turn, wheel M turn will be slower as well as wheel N which will take more time.
Therefore, In the case above, It will take more time for a tooth of wheel B and C to make a full turn than it will for a tooth of wheel A.
Learn more about Gear wheels from
https://brainly.com/question/17080981
#SPJ1