A stream of air flowing at a rate of 10.0 kg/h is mixed with a stream of CO2. The CO2 enters the mixer at a rate of 30.0 SCMH. The actual temperature of the CO2 stream is 250°C and 3 bar.
a) What is the true volumetric flow rate of the CO2 stream?
b) What is the mole percent of CO2 in the product stream?

Answer:

Find explanation below.

Explanation:

Seed drills make it possible for seeds to be planted at equal spacing or distances.

Seed drills are important because they allow seeds to be planted at specific depths and distances. This allows for increased crop yield. They also help to curb the growth of weeds.

In the radio communication system, multipath is the propagation phenomenon that causes diffusion or reflection in multiple different directions of a signal.

Multipath is a propagation mechanism that impacts the propagation of signals in radio communication. Multipath results in the transmission of data to the receiving antenna by two or more paths. Diffusion and reflection are the causes that create multiple paths for the signal to be delivered.

Diffraction occurs when a signal bends around sharp corners; while reflection occurs when a signal impinges on a smooth object. When a signal is received through more than one path because of the diffraction or reflection, it creates phase shifting and interference of the signal.

You can learn more about signal propagation at

https://brainly.com/question/14452898

#SPJ4

Answer:

Explanation:

The image that is supposed to be attached to the question is displayed in the diagram below.

Applying Nodal Analysis at node 1;

\(\dfrac{V_o -50}{12.5*10^{-3}} + \dfrac{V_o}{50*10^3}+\dfrac{V_o-7500 \ in}{10*10^3}=0\)

where;

\(in = \dfrac{V_o}{50*10^3}\)   (from the circuit)

= \(\dfrac{V_o-50}{12.5}+\dfrac{V_o}{50} + V_o -\dfrac{7500 *V_o }{\frac{50*10^3}{10}}=0\)

= \(V_o [ \dfrac{1}{12.5}+\dfrac{1}{50}+\dfrac{1}{10}-\dfrac{75}{500}] = \dfrac{50}{12.5}\)

= \(V_o[ \dfrac{500*500+12.5*5000+12.5*5000*5-75*12.5*500}{12.5*50*10*500}]= \dfrac{50}{12.5}\)

= \(V_o = 80 \ volts\)

\(in = \frac{80}{50*10^3}= 1.6 mA \\ \\ 7500*in = 120 volts \\ \\ I = \frac{120-80}{10(10^3} =4*10^{-3} Amps \\ \\ \\ \\ P_{generated} = 75000*in*I \\ \\ P_{generated} = 120*4*10^{-3} \\ \\ P_{generated} = 480 \ MW\)

The displacement of end D with respect to end A is \(-0.488 \times 10^{-3}\;m\)

Given the following data:

To determine the displacement of end D with respect to end A:

First of all, we would do a sectional cut of the circular rods at point A and then determine the sum of forces acting on it:

\(\sum F=0\\\\ 10000+N_1=0\\\\N_1 = -10000\;N\)

Mathematically, the displacement of a circular rod is given by this formula:

\(d = \frac{NL}{AE}\)

Where:

Substituting the given parameters into the formula, we have;

\(d_1 = \frac{-10000 \times 0.435}{\frac{3.142 \times 0.02^2}{4} \times 68.9 \times 10^9} \\\\d_1 = \frac{-4350}{0.0003142 \times 68.9 \times 10^9}\\\\d_1 =-0.201 \times 10^{-3}\;meter\)

For section cut BC:

\(\sum F=0\\\\ 10000-20000+N_2=0\\\\N_2 = 10000\;N\)

\(radius = outer\;radius^2 - inner\;radius^2\\\\radius = 0.04^2 -0.03^2=0.0007\;m\)

\(d_2 = \frac{10000 \times 0.435}{\frac{3.142 \times 0.0007^2}{4} \times 68.9 \times 10^9} \\\\d_2 = \frac{4350}{0.00054985 \times 68.9 \times 10^9}\\\\d_2 =0.115 \times 10^{-3}\;meter\)

For section cut D:

\(\sum F=0\\\\ -20000-N_3=0\\\\N_3 =- 20000\;N\)

\(d_3 = \frac{-20000 \times 0.435}{\frac{3.142 \times 0.02^2}{4} \times 68.9 \times 10^9} \\\\d_3 = \frac{-8700}{0.0003142 \times 68.9 \times 10^9}\\\\d_3 =-0.402 \times 10^{-3}\;meter\)

For the total displacement:

The total displacement is equal to the displacement of end D with respect to end A.

\(d_T = d_1 +d_2+d_3\\\\d_T = -0.201 \times 10^{-3} + 0.115 \times 10^{-3}-0.402 \times 10^{-3}\\\\d_T = -0.488 \times 10^{-3}\;m\)

Read more on displacement here: https://brainly.com/question/25690629

The classification of the working surfaces are as follows;

A working surface is a flat surface on which various activities can be carried out.

In a construction system, the duty carried on a particular working surface varies from another. They can be categorized into heavy-duty, medium-duty, light-duty, and very light-duty.

The classification of the working surfaces are as follows;

Learn more about the working surface here:

https://brainly.com/question/16508484

Answer:

Pattern as in texture is easy to see any flaws in your 3D design.

Explanation:

The wired networking standard that specifies the order in which data is sent through the network is Ethernet.

Ethernet is a widely used wired networking standard that defines the protocols and specifications for data transmission over a local area network (LAN). It specifies the order in which data is sent through the network by utilizing the Carrier Sense Multiple Access with Collision Detection (CSMA/CD) algorithm.

The CSMA/CD algorithm ensures that multiple devices connected to an Ethernet network can share the same communication medium without interfering with each other. Before transmitting data, a device using Ethernet listens to the network to detect if it is clear to send data. If the network is busy, it waits for an opportune moment. Once the network is clear, the device sends the data, constantly monitoring for collisions. If a collision occurs (when two or more devices transmit data simultaneously), they stop transmitting, wait for a random period of time, and then retry.

By following this protocol, Ethernet ensures orderly and efficient data transmission within the network, minimizing collisions and maximizing data throughput. It has become the de facto standard for wired local area networks due to its reliability, scalability, and widespread adoption.

Learn more about Ethernet

brainly.com/question/31610521

#SPJ11

Answer:

d. all of the statements are correct.

Explanation:

WiMAX Broadband Wireless Access has the capacity to provide service up to 50 km for fixed stations. It has capacity of up to 15 km for mobile stations. WiMAX BWA describes both of 4G mobile WiMAX and fixed stations WiMAX. OFMD is used to increase spectral efficiency of WiMAX and to improve noise performance.

Answer:

#include <iostream>

using namespace std;

class EvenNumber

{

   private:

   int integrer;

   public:

   EvenNumber ()

   {

       integrer=0;

   }

   EvenNumber (int number)

   {

   integrer=number;

   }

   int getvalue ()

   {

       return integrer;

   }

   int getnext ()

   {

       return integrer+2;

   }

   int getprevious ()

   {

       return integrer-2;

   }

};

int main () {

   EvenNumber sixteen(16);

   cout<<"The value is: "<<sixteen.getvalue()

   <<" the next even number is: "<<sixteen.getnext()<<

   " and the previous number is: "<<sixteen.getprevious();

   return 0;

}

Explanation:

The three types of irony are Verbal Irony, Situational Irony, and Dramatic Irony.

Example of Verbal Irony:

Example of Situational Irony:

Example of Dramatic Irony:

What is Irony?

When something unexpected occurs, it is ironic. The thing opposite to what we anticipate usually occurs, and this is either humorous or dramatic.

To learn more about Irony:

https://brainly.com/question/24267033

#SPJ4

Answer:

$270

Explanation:

Formulate the following based on the given conditions: 3x 80 Determine the product or quotient is 240

A savings account is a simple type of financial product that allows you to deposit funds and earn a small amount of interest. These accounts are federally insured up to $250,000 per account owner and provide a secure place for your money to grow while earning interest.

A savings account is a simple type of financial product that allows you to deposit funds and earn a small amount of interest. These accounts are federally insured up to $250,000 per account owner and provide a secure place for your money to grow while earning interest.

While there are several types of savings accounts, the deposit account, money market account, and certificate of deposit are the three most common.

Therefore, Lara has three savings accounts into which she distributes her money each pay check; if she puts at least $80 in each account this pay period, she can earn $240.

To learn more about savings accounts, refer;

brainly.com/question/25787382

#SPJ2

We create, maintain, and live by often unspoken rules and routines that we hope will keep the family (and each of its members) functional.

What are unspoken rules in families?

There are unspoken guidelines that family members follow in order to maintain order in families dealing with substance use disorders. These guidelines are: Don't trust, don't feel, and don't talk. To keep things as they are, those who are a part of the system abide by these norms.

Why is it important to have family rules?

Children learn what acts are acceptable and unacceptable from their family's rules. As kids get older, they will encounter situations where they must abide by rules. Children who learn to follow rules at home will likely learn to do so elsewhere.

Learn more about family rules: https://brainly.com/question/14740656

#SPJ4

The criteria for a guard having to be used on a machine is;

As a safety measure If the operation exposes you to an injury.

When operating a machine, there are possibilities that the operator could be injured or exposed to injury.

Due to the possible safety issues when operating a machine, the Occupational Safety and Health Administration (OSHA) in their 29 code mandated that a safeguard must be put at each machine to ensure that there is adequate safety that prevents or minimizes the risk of getting injured.

Read more on Occupational Safety and Health Administration (OSHA) rules at; https://brainly.com/question/17069021

Answer:

Work is the amount of energy transfered by a force.

Energy is the amount of power an object gets from its position or motion.

Power is the combination of all forces and movements of a system that is the rate at which work can be done by a system.

Anemometer

Explanation:

An anemometer is a device used for measuring wind speed and direction. It is also a common weather station instrument. The term is derived from the Greek word anemos, which means wind, and is used to describe any wind speed instrument used in meteorology.

The statement is true. Time needed to process one flow unit. = Ratio of theoretical flow time to actual flow time of a certain process.

The total of the activity times of the tasks that make up the critical path. It excludes waiting time. Less Space is Needed. Less space and labor are needed to handle (receive, count, stock, keep, pick, and deliver) decreasing inventory levels. A single operator can supervise numerous pieces of equipment while moving around very little thanks to one piece flow, which produces workcells with optimized equipment arrangement. Determine the task whose throughput is the lowest.

Learn more about equipment here-

https://brainly.com/question/24846558

#SPJ4

Answer:

234567891234567891234567891 what is this?????

Explanation:

234567891234567891234567891

IS THIS IS A QUESTION

OH DON'T MIND JUST ASKING

BTW

GOOD MORNING/AFTERNOON/EVENING/NIGHT

HOW ARE YOU

HAVE A GREAT DAY AHEAD

PLS MARK ME AS BRAINLIEST

An environmental hazard is a substance, state or event which has the potential to threaten the surrounding natural environment and/or adversely affect human's health. This term incorporates topics like pollution, natural disasters and human-made hazards. Health studies investigate the human health effects of exposure to environmental hazards ranging from chemical pollutants to natural, technological or terrorist disasters. The environment in which we live can be considered as having three fundamental sets of components, physical, chemical, biological. Associations between an exposure and an adverse health effect do not, on their own, prove that the former is the cause of the latter. Many other non-causal associations could explain the findings. Physical hazards involve environmental hazards that can cause harm with or without contact. Examples are earthquakes, electromagnetic fields, floods, light pollution, noise pollution, vibration, x-rays etc. Radioactivity is associated with an exposure dependent risk of some cancers notably leukaemia. The scientific evidence of adverse health effects from general environmental exposure to these fields is "not proven". If there are adverse effects yet to be proven, the risk is probably likely to be small. Chemical substances cause significant damage to the environment. Tobacco smoke is the single biggest known airborne chemical risk to health, whether measured in terms of death rates or ill-health. To a much lesser degree of risk, these adverse effects apply to non-smokers exposed passively to sidestream tobacco smoke. Health effects of concern are asthma, bronchitis, lung cancer and similar lung diseases, and there is good evidence relating an increased risk of symptoms of these diseases with increasing concentration of Sulphur dioxide, ozone and other pollutants. Biohazards generally fall into two broad categories: those which produce adverse health effects through infection (microorganisms, viruses or toxins) and those which produce adverse effects in non-infective (allergic) ways.

Hope this helps...:)

ᴄᴏᴍᴘʟᴇᴛᴇɴᴇꜱꜱ ᴍᴇᴀɴꜱ ᴛʜᴇ ꜱᴛᴀᴛᴇ ᴏꜰ ʙᴇɪɴɢ ᴄᴏᴍᴘʟᴇᴛᴇ ᴀɴᴅ ᴇɴᴛɪʀᴇ; ʜᴀᴠɪɴɢ ᴇᴠᴇʀʏᴛʜɪɴɢ ᴛʜᴀᴛ ɪꜱ ɴᴇᴇᴅᴇᴅ.

ʙᴇᴀᴜᴛʏ ᴍᴇᴀɴꜱ combination of qualities, such as shape, colour, or form, that pleases the aesthetic senses, especially the sight.

The board's analogue input pin A2 is connected to the potentiometer's middle pin.

A three-terminal resistor with a sliding or rotating contact that creates a variable voltage divider is what is meant by this term. Only two terminals, one end, and the wiper, are required for the potentiometer to function as a rheostat or variable resistor.

The potentiometer is a device used to gauge the unknown voltage by contrasting it with the established voltage. It can be used to calculate the emf and internal resistance of the specified cell as well as to compare the emf of various cells.

Both linear and rotary potentiometers are common types of potentiometers.

To learn more about potentiometer refers to:

brainly.com/question/25606721

#SPJ4

Sure, I can help you with that!

To add self-checking to a constrained random stimulus testcase, you'll need to include a mechanism to verify the correctness of the results produced by the DUT (Device Under Test) against an expected output. This can be achieved using assertions or coverage analysis.

Here's an example code snippet that demonstrates how to add self-checking to a constrained random stimulus testcase:

```systemverilog
module top;
 // Declare the DUT and input/output ports
 dut dut_inst();
 logic [3:0] in_data;
 logic [3:0] out_data;

 // Instantiate a randomization object
 randcase rand_data;
   rand bit [3:0] in_data;
 endcase

 // Constrained random stimulus testcase
 initial begin
   repeat(10) begin
     // Randomize input data
     rand_data = new();
     rand_data.randomize();

     // Assign input data to DUT inputs
     in_data = rand_data.in_data;
     dut_inst.in = in_data;

     // Execute the DUT
     #10;
     out_data = dut_inst.out;

     // Check output data against expected value
     assert(out_data == in_data + 1) else
       $error("Incorrect output data: Expected %d, but got %d", in_data + 1, out_data);
   end
 end
endmodule
```

In this code, we have a `randcase` block that generates random input data for our DUT. We then assign this data to the input ports of the DUT and execute it. After the DUT has produced its output, we use an `assert` statement to compare the output against the expected value (`in_data + 1` in this case).

If the assertion fails, an error message is printed to the console indicating the expected and actual output values. This allows us to easily identify any issues with the DUT's behavior and make necessary corrections.

Learn more about random stimulus: https://brainly.com/question/251701

#SPJ11

When a function has a basic period of the type f(x+k)=f(x) f(x+k)=f(x), k is referred to as the period of the function, and f is referred to as a periodic function.

A function is a kind of rule that, for one input, it gives you one output. Image source: by Alex Federspiel. An example of this would be y=x2. If you put in anything for x, you get one output for y. We would say that y is a function of x since x is the input value.

i) For periodic signal x1(t+T1)=x1(t)

==> cos(t+T1)=cos(t)

The above equation will hold for T1=2nπ

Thus, the fundamental period will be T1=2π

ii) For periodic signal x1(t+T1)=x1(t)

==> sin(π(t+T2))=sin(πt)

==> sin(πt+πT2))=sin(πt)

The above equation will hold for πT2=2nπ

Thus, the fundamental period will be T2=2

b) Now, for x3(t)

to be periodic k_2 \over k_1=T_1 \over T_2

==> k_2 \over k_1=2\pi \over 2=\pi

Since, π

is not an integer Hence, x3(t) is not periodic c) i) P(x1(t))=12π∫20\picos2(t)dt

==> P(x1(t))=14π∫20π(1+cos(2t))dt

==> P(x1(t))=14π[1+0.5sin(2t)]20π

==> P(x1(t))=12

To know more about function visit:-

https://brainly.com/question/12431044

#SPJ1

echo $CREATOR is the commands that will display the contents of the variable to standard output. Hence option a is correct.

Variable is defined as a value that is subject to vary depending on external factors or input to the program. A program normally consists of instructions that tell the computer what to do and data that it utilizes while running.

A Unix/Linux command tool called echo is used to show lines of text or strings that are supplied as command-line parameters. One of the fundamental commands in Linux, this one is most frequently used in shell scripts.

Thus, echo $CREATOR is the commands that will display the contents of the variable to standard output. Hence option a is correct.

To learn  more about variable, refer to the link below:

https://brainly.com/question/17344045

#SPJ1

The output force, or Fout, produced by a lever depends on the length of the lever arm, or rout, and the input force applied to the lever. The formula for calculating Fout is Fout = Fin x (rin/rout), where Fin is the input force and rin is the length of the input arm.

For more such question on motion

https://brainly.com/question/25951773

#SPJ11

Answer:

mark me as a brainleast

Explanation:

209781

Answer:l=legend

Explanation:basically L = legend and Q=Quick

The three formula for finding out the 3 types of the slope of curve Q with respect to L should be explained below.

1. Slope intercept form where the formula is y = mx + b

Here

y = variable

m = slope of line

x = variable

b = y intercept

2. Point slope form where the formula is y - y1 = m(x - x1)

Here

y = variable

y1 = y coordinate at the first point on line

m = the slope

x = variable

x1 = x coordinate at the first point on line

3. Standard slope form where the formula is ax + by = c

Here

a = x coefficent

b & c = constant term

learn more about formula here: https://brainly.com/question/24454271

The red brake warning lamp (RBWL) can be triggered by hydraulic system failure, low brake fluid level, and during a bulb check. Option D is correct.

The red brake warning lamp (RBWL) is a dashboard indicator that alerts the driver to a problem with the braking system. This warning lamp can turn on for various reasons, including:

If there is a problem with the hydraulic brake system, such as a leak in the brake lines or a malfunctioning brake component, the RBWL will turn on to alert the driver.

If the brake fluid level is low, the RBWL will turn on to alert the driver that the brakes may not function properly.

The RBWL will turn on briefly during a bulb check when the driver turns on the ignition, but the light should turn off once the engine starts.

Therefore, the correct answer is (d) All of the above.

Learn more about red brake warning lamp https://brainly.com/question/15712156

#SPJ11